Phone : +86 18138709418
Email : sales9@pikespool.comSAPHIR©
HJ2042
USER MANUAL
Thank you for purchasing Winny Robotic Pool Cleaner. If you have any questions or issues, please contact your local dealer for customer service.
Contents
Important Precautions PAGEREF _Toc27400060 \h 1
Attention PAGEREF _Toc27400061 \h 2
I. Introduction PAGEREF _Toc27400062 \h 3
II. Safety PAGEREF _Toc27400063 \h 3
III. Specifications PAGEREF _Toc27400064 \h 4
IV. Operations PAGEREF _Toc27400065 \h 5
4.1 Panel PAGEREF _Toc27400066 \h 5
4.2 Remote control (Optional) PAGEREF _Toc27400067 \h 7
4.3 Filter cleaning PAGEREF _Toc27400068 \h 8
V. Assembly of transport caddy (Optional) PAGEREF _Toc27400069 \h 9
VI. Packing list PAGEREF _Toc27400070 \h 10
Important Precautions
1. Please read the manual carefully, and use the cleaner according to the manual. We are not held liable for any loss or injury caused by improper use.
2. Please do not allow children to ride on it or play with it as a toy.
3. In order to prevent severe damage to the cleaner, never power on it when it is out of the swimming pool.
4. It is forbidden to operate the cleaner when there are people in the pool, and the power supply should be connected to a leakage-protected and earthed socket.
5. In order to avoid overheating and potential damage for components, never cover the power supply.
6. In order to avoid any accident or damage, it is strongly recommended to fix the power supply indoor in at least 3.5m away from the swimming pool edge and connect the power supply with a fixed holder by using the safety rope.
7. Before power-on, make sure the filters be assembled and the cable be fully released to avoid any winding, which could affect the cleaner’s performance or cause damage.
8. Hold the top handle when putting the cleaner into or lift it out of the water. Do not pull the cable.
9. It is forbidden to use the cleaner beyond its working conditions stated in the manual.
10. The cleaner should be stored in a cool and ventilated place, away from direct sunshine.
11. Only professionals can disassemble the cleaner and its power supply, otherwise the warranty will be invalidated.
12. It is forbidden to drop and hammer the cleaner and power supply.
13. Use the accessories recommended or sold by the manufacturer only.
14. It is strictly forbidden to place chemicals for water treatment inside the cleaner for spraying, otherwise the warranty will be invalidated.
1. Put into or lift out of the pool with the cleaner bottom towards the wall to avoid any possible scratches to the pool. Hold the top handle and put it into the pool. Let the cleaner immerse into the pool floor after emptying the air inside it (the air inside should be exhausted completely, otherwise its normal working will be affected).
2. Please hold the top handle only and never pull the cable when lifting it out of the pool.
The robotic pool cleaner HJ2042 is a new type of highly efficient and energy-saving swimming pool cleaning robot. Through its advanced computer-controlled program, it can clean the pool walls and bottom automatically. At the same time, it filters the pool water and gets rid of suspended particles without replacing the pool water. It is totally environmental-friendly.
For safe operation, the cleaner works on 20V direct current.
Please read this user manual carefully before use.
Power supply needs to be placed in a proper position so as to reach the coverage for the whole pool, meanwhile as least 3.5m away from the swimming pool edge.
1. Rated input voltage: 220VAC (230VAC)/110VAC (120VAC)
2. Frequency: 50Hz/60Hz
3. Output voltage: DC20V
4. Power: 200W
5. Cleaning cycle: 1H/1.5H/2H
6. Cable length: 18m
7. Auto-start timer: 1D/3D/7D
8. Filter capacity: appr. 20m³/h
9. Filter density: 100μm/200μm/400μm
10. Moving speed: appr. 12.5m/min
11. IP grade: Cleaner IPX8; Power supply: IPX5
12. Max. water depth: 2m
13. Working temperature: 0°C-40°C
14. Remote distance: >20m
15. Frequency of remote control: 433MHz
No. |
Sign |
Function |
Instruction |
||
1 |
ON/OFF |
Power on/off |
Press this button, the cleaner starts to work; Press a second time, the cleaner is stopped. |
||
2 |
TIME |
To choose working cycle |
When the cleaner is on, press this button to choose preferred working cycle. |
||
3 |
AUTO START |
Auto-start timer |
This function allows self-starting for the programmed days. When the cleaner is stopped, the indicator goes out in 5 seconds and into standby. When the three “1D”, “3D” and “7D” indicators are all off, press AUTO START to see if it is on. If the three indicators flash at the same time, it means that it is not in use. |
||
4 |
Indicators |
TIME indicators |
1H flashes |
Cleaner running for 1 hour |
|
1.5H flashes |
Cleaner running for 1.5 hours |
||||
2H flashes |
Cleaner running for 2 hours |
||||
1H, 1.5H and 2H flash together |
Working cycle finished |
||||
Auto-start indicators |
1D constant |
Auto-start every day established |
|||
3D constant |
Auto-start every 3 days established |
||||
7D constant |
Auto-start every 7 days established |
||||
1D, 3D, 7D flashes |
Auto-start timer is not in use |
||||
|
Fault Code |
Trouble |
Suggestion |
||
Fault |
1H and 1.5H flash together, with warning sound |
Pump is overloaded |
Stop the cleaner, check if anything is stuck in the impeller |
||
1.5H and 2H flash together, with warning sound |
Driving motor is overloaded |
Stop the cleaner, check if anything is stuck in the belt |
|||
1H and 2H flash together, with warning sound |
Cleaner out of water |
Exhaust the air inside the cleaner, immerge the cleaner and restart it. |
4.2 Remote control (Optional)
No. |
Sign |
Function |
Instruction |
1 |
|
Antenna |
Signal reception |
2 |
|
Indicator |
Indicates status |
3 |
1.5H |
Cleaner running for 1.5 hours |
Press the button, then the cleaner will work for 1.5 hours |
4 |
2H |
Cleaner running for 2 hours |
Press the button, then the cleaner will work for 2 hours |
5 |
STOP |
Stop working |
Press the button, then the cleaner will stop working |
6 |
1H |
Cleaner running for 1 hour |
Press the button, then the cleaner will work for 1 hour |
7 |
▲ |
Manual-Walk forward |
Press the button, then the cleaner will walk forward |
8 |
▼ |
Manual-Walk backward |
Press the button, then the cleaner will walk backward |
Note: Switching between automatic mode and manual mode needs to stop the cleaner by pressing STOP.
1. Unscrew the cover then remove it
2. Pull 2 filters up and remove 2 filters
3. Clean the filters
4. Slide the two filters into the grooves, replace the cover and screw the fastener
V. Assembly of transport caddy (Optional)
1. Open the package for assembling 2. Put the connection part onto the plate
3. Insert the wheel axle 4. Assemble the protecting cover and axle cover
5. Assemble wheels 6. Put on the nut
7. Tighten the nut 8. Assemble the top handle
9. Assemble power supply holder 10. Assemble cable holder
No. |
Item |
Name |
Model |
QTY (pc) |
Remark |
1 |
Cleaner |
Cleaner body |
HJ2042 |
1 |
In carton |
2 |
Power supply |
HJ2042 |
1 |
In carton |
|
3 |
User manual & safety rope |
|
1 |
In plastic bag |
|
4 |
Foam |
|
4 |
In plastic bag |
|
5 |
Filter bag |
100μm & 200μm |
4 |
In plastic bag |
|
6 |
Remote control (Optional) |
|
1 |
In plastic bag |
|
7 |
Transport caddy (Optional) |
Top handle |
|
1 |
In carton |
8 |
Connection part |
|
1 |
In carton |
|
9 |
Plate |
|
1 |
In carton |
|
10 |
Power supply holder |
|
1 |
In carton |
|
11 |
Cable holder |
|
1 |
In carton |
|
12 |
Wheel axle |
|
1 |
In carton |
|
13 |
Wheel |
|
2 |
In carton |
|
14 |
Nut |
M10 |
2 |
In plastic bag |
|
15 |
Axle cover |
|
2 |
In plastic bag |
|
16 |
Protecting cover |
|
2 |
In plastic bag |
This product has passed all quality control and safety tests, conducted by the technical department of the factory.
Warranty information:
1. The warranty is covered for 24 months (only for motors and PCB) from the date of its original purchase.
2. This warranty is void if the product has been altered, misused, or has been repaired by unauthorized personnel.
3. The warranty extends only to manufacturing defects and does not cover any damage resulting from mishandling of the product by the owner.
4. The sales invoice must be presented for any claim or repair during the warranty period.
Please contact your local dealer for any warranty issues.
Instructions for installation of foams
Stick two small foam on the back side of the top cover if the cleaner is difficult to climb to the waterline.
1. Stick two small foams on the proposed positions of the top cover (foam with the sticker on its back)
2. Install the foams as described below:
(1) Remove the protection from the sticker
(2) Stick B side
(3) Stick A side in the correct position
Note: Put it into the pool 24 hours later.